Re: kernel 2.6.6 - chyby hdb pri shutdownu

[Martin Slouf <xslom03 zavinac vse bod cz>]

hlasky tohohle typu znaci, ze je pevny disk v haji (respektive, ovladac si 
mysli, ze je v haji (zazil jsem to :( )

zkuste neco jako 'ide-smart -d /dev/hdb'
(na debianu je to balik 'ide-smart')
vystup prikazu by mel obsahovat hodnoty value a treshold -- rozumim tomu 
jen do te miry, ze pokud jsou hodnoty treshold vysoke (tj. vyssi nez 
value), je disk na odpis.

trvalo mi tak 2 dny normalniho pouzivani, nez disk odesel zcela uplne, po 
te, co se hlasky zacaly vypisovat.

nicmene je mozny, ze je to chyba v 2.6.6, pokud downgrade na 2.6.5 nic 
podobnyho netvrdi.

m.


On Wed, 12 May 2004, Kotrla Vitezslav wrote:

> Kernel 2.6.6 mi zacal pri vypinani psat neco, co 2.6.5 nepsal, a nevim,
> zda me to ma znepokojovat. Nasleduje peclivy opis obrazovky pri
> shutdownu (screen capture pomoci utility Minolta F100):
> 
>   ...
>   Deconfiguring network interfaces...done.
>   Deactivating swap...done.
>   Unmounting local filesystems...done.
>   Shutdown: hdb
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   hda: DMA disabled
>   hdb: DMA disabled
>   ide0: reset: success
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   ide0: reset: success
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: status=0x04 { DriveStatusError }
>   Shutdown: hda
>   Power down.
>   acpi_power_off called
>   <blik cvak cink cerna obrazovka>
> 
> Vsiml jsem si, ze se ten DriveStatusError objevil i pri startu. Kernel 2.6.5
> s tim problem nemel. Nasleduje kus dmesg:
> 
>   ...
>   Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>   ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>   VP_IDE: IDE controller at PCI slot 0000:00:11.1
>   VP_IDE: chipset revision 6
>   VP_IDE: not 100% native mode: will probe irqs later
>   VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
>       ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:DMA
>       ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:pio, hdd:DMA
>   hda: MAXTOR 6L060J3, ATA DISK drive
>   hdb: Maxtor 6Y120P0, ATA DISK drive
>   ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>   hdd: JLMS XJ-HD165H, ATAPI CD/DVD-ROM drive
>   ide1 at 0x170-0x177,0x376 on irq 15
>   hda: max request size: 128KiB
>   hda: 117266688 sectors (60040 MB) w/1819KiB Cache, CHS=65535/16/63, 
> UDMA(100)
>    hda: hda1 hda2 hda3
>   hdb: max request size: 128KiB
>   hdb: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, 
> UDMA(100)
>    hdb: hdb1 hdb2 hdb3 hdb4
>   hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
>   hdb: task_no_data_intr: error=0x04 { DriveStatusError }
>   hdb: Write Cache FAILED Flushing!
>   ...
> 
> Pouzivam Debian (Sarge), jadro je plain vanilla z kernel.org.
> 
> Diky za kazdy napad ci dokonce vysvetleni ;-)
> 
> Vitezslav Kotrla
> ________________________________________________
> CZdebian-l maillist  -  CZdebian-l zavinac debian bod cz
> http://www.debian.cz/mailman/listinfo/czdebian-l
> E-mail (un)subscriptions: czdebian-l-request zavinac debian bod cz
>