kernel 2.6.6 - chyby hdb pri shutdownu

["Kotrla Vitezslav" <kotrla zavinac ceb bod cz>]

Kernel 2.6.6 mi zacal pri vypinani psat neco, co 2.6.5 nepsal, a nevim,
zda me to ma znepokojovat. Nasleduje peclivy opis obrazovky pri
shutdownu (screen capture pomoci utility Minolta F100):

  ...
  Deconfiguring network interfaces...done.
  Deactivating swap...done.
  Unmounting local filesystems...done.
  Shutdown: hdb
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  hda: DMA disabled
  hdb: DMA disabled
  ide0: reset: success
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  ide0: reset: success
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: status=0x04 { DriveStatusError }
  Shutdown: hda
  Power down.
  acpi_power_off called
  <blik cvak cink cerna obrazovka>

Vsiml jsem si, ze se ten DriveStatusError objevil i pri startu. Kernel 2.6.5
s tim problem nemel. Nasleduje kus dmesg:

  ...
  Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
  ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
  VP_IDE: IDE controller at PCI slot 0000:00:11.1
  VP_IDE: chipset revision 6
  VP_IDE: not 100% native mode: will probe irqs later
  VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
      ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:DMA
      ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:pio, hdd:DMA
  hda: MAXTOR 6L060J3, ATA DISK drive
  hdb: Maxtor 6Y120P0, ATA DISK drive
  ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
  hdd: JLMS XJ-HD165H, ATAPI CD/DVD-ROM drive
  ide1 at 0x170-0x177,0x376 on irq 15
  hda: max request size: 128KiB
  hda: 117266688 sectors (60040 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(100)
   hda: hda1 hda2 hda3
  hdb: max request size: 128KiB
  hdb: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(100)
   hdb: hdb1 hdb2 hdb3 hdb4
  hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
  hdb: task_no_data_intr: error=0x04 { DriveStatusError }
  hdb: Write Cache FAILED Flushing!
  ...

Pouzivam Debian (Sarge), jadro je plain vanilla z kernel.org.

Diky za kazdy napad ci dokonce vysvetleni ;-)

Vitezslav Kotrla